axial silastic guard junction standard rectifier e-mail: sales@cnmic.com web site: www.cnmic.com voltage range 50 to 1000 volts 6a05g thru 6a10g current 6.0 ampere features glass passivated chip junction low reverse leakage low forward voltage high forward surge current capability high temperature soldering guaranteed 260 /10 seconds,0.375 (9.5mm)lead length mechanical data case: transfer molded plastic epoxy: ul94v-0 rate flame retardant polarity: color band denotes cathode end lead: plated axial lead, solderable per mil-std-202e method 208c mounting position: any weight: 0.07ounce, 2.0 gram maximum ratings and electrical characteristics ratings at 25 ambient temperature unless otherwise specified single phase, half wave, 60hz, resistive or inductive load for capacitive load derate current by 20% symbols 6a 05g 6a 1g 6a 2gg 6a 4g 6a 6g 6a 8g 6a 10g unit maximum repetitive peak reverse voltage v rrm 50 100 200 400 600 800 1000 volts maximum rms voltage v rms 35 70 140 280 420 560 700 volts maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 volts maximum average forward rectified current 0.375 (9.5mm) lead length at t a =60 i (av) 6.0 amps peak forward surge current 8.3ms single half sine wave superimposed on rated load (jedec method) i fsm 250 amps maximum instantaneous forward voltage at 6.0a v f 0.95 volts t a = 25 10.0 maximum dc reverse current at rated dc blocking voltage at t a = 100 i r 500 a maximum full load reverse current, full cycle average 0.375(9.5mm) lead length at t l =105 i r(av) 500 a typical junction capacitance (note 2) c j 100 pf typical thermal resistance (note 1) r ja 10 /w operating temperature range t j (-55 to +150) storage temperature range t stg (-55 to +150) notes: 1. thermal resistance from junction to ambient with 0.375 (9.5mm) lead length, pcb. mounted with 1.1 1.1 (30mm 30mm) copper pads. 2. measured at 1.0 mhz and applied reverse voltage of 4.0v dia. .052(1.3) .048(1.2) 1.0(25.4) min. .360(9.1) .340(8.6) 1.0(25.4) min. dia. dimensions in inches and (millimeters) r-6 .360(9.1) .340(8.6)
axial silastic guard junction standard rectifier e-mail: sales@cnmic.com web site: www.cnmic.com voltage range 50 to 1000 volts 6a05g thru 6a10g current 6.0 ampere fig.2-maximum non-repetitive peak 100 t jmax 40 20 10 2 300 200 100 1 c u r r e n t , ( a ) p e a k f o r w a r d s u r g e number of cycles at 60 hz 8.3ms single half sine-wave (jedec method) t= forward surge current derating curve fig.1-typical forward current 150 175 125 75 100 4.0 50 2.0 0 0 60 hz resistive or surface area inductive loads ground plane 25 a v e r a g e f o r w a r d c u r r e n t , ( a ) fig.3-typical instantaneous forward characteristics ambient temperature, ( c) ( a ) 1.4 j t =25 c 1.2 1.0 0.8 0.6 1% duty cycle pulse width=300us 10 1.0 0.1 1000 100 instantaneous forward voltage,(v) fig.5-typical junction capacitance 0.1 10 reverse voltage,(v) vsig=50mvp-p j u n c t i o n c a p a c i t a n c e , ( p f ) i n s t a n t a n e o u s r e v e r s e c u r r e n t , 1.61.82.0 recommended p.c. board f=1mhz t =25 c 468 1 cycle 60 1.010100 j reverse voltage,(%) percent of rated peak 20 120 140 0 0.01 20 0.1 1.0 100 60 40 80 t =25 c j fig.4-typical reverse 10 characteristics t =100 c j 1.0 3.0 5.0 6.0 60 mounting 1 1 copper p.c.board 400 250 80 100 1000 70 60 50 30 40 20 10 0 00.20.40.60.81.0 single lead to heat sink, insignificant heat flow through other lead equal length both leads to heat sink, equal lead length to heat sink(in.) t h e r m a l r e s i s t a n c e , r ( c / w ) j l vs lead length fig.6-typical thermal resistance i n s t a n t a n e o u s f o r w a r d c u r r e n t , ( a ) ( a ) rating and chracteristic curves 6a05s thru 6a10s
|
